Skip to main content

Tool Board D Reading and Viewing

  • Before searching for the ID, connect the tool board to a UTOC or a mainboard flashed with bridge firmware using an XT30 data cable. Refer to the wiring diagram below:

    Loading...

  • Ensure that the resistance between CAN H and CAN L, measured with a multimeter while powered off, is around 60Ω. If it is 120Ω, connect a 120Ω jumper. If it is around 40Ω, remove the jumper.

    Loading...

    Complete Guide to CAN Toolboard Setup​

    Preparations​

    Important Prerequisites
    • Toolboard Status: Ensure the toolboard is flashed with Klipper-can firmware or is in Katapult-can mode.
    • Important Note: This tutorial is only for searching Toolboard IDs, not for Mainboard IDs.
    • Connection Requirements: The toolboard must be connected to one of the following devices:
      • A UTOC module.
      • A mainboard flashed with USB Bridge CAN firmware.
    • Final Connection: The above device must be connected to the host computer.

    CAN Network Configuration Requirements​

    • Default Configuration: This tutorial assumes the host computer's CAN network is already configured.
    • Fly Users: If using a Fly host computer running the Fly-FAST system, CAN is configured by default (rate: 1Mbps).
    • First-time Users: Please read the tutorial below first: CAN Configuration Tutorial

    Connect via SSH​

    • Log in to SSH over the network (do not use serial port login).
    • Ensure the host computer is properly connected to the CAN network device.

    Search for CAN ID​

    • Search command for standard host computers: 
      ~/klippy-env/bin/python ~/klipper/scripts/canbus_query.py can0
    • Search command for FLY host computers: 
      python3 ~/klipper/scripts/canbus_query.py can0

    Search Result Explanation​

    CANID
    • Important Note: The mainboard ID has already been configured in Klipper in previous documentation. Under normal circumstances, the mainboard's CANID cannot be found via search.
    • Quick Verification Method: If confirmation is needed, first disconnect the CAN cable between the mainboard and the toolboard, then re-run the search.
    • After executing the search command, the following situations may occur:
    Result DisplayStatus DescriptionNext Steps
    Application: KlipperDevice is flashed with Klipper firmware.This ID can be used directly.
    Application: CANBOOT or KatapultDevice is in Bootloader mode.Needs to be flashed with Klipper firmware before use.
    Total 0 uuids foundNo devices found.Please check the following:
    1. Is the CAN network configured correctly?
    2. Is the CAN rate consistent? (Default: 1Mbps)
    3. Is this ID already used in the configuration? (Need to comment it out, save, power off, and restart.)
    Loading...
    About Duplicate IDs

    If a device ID is already configured in printer.cfg, it will not appear in the search results. To search for it again, please:

    1. Comment out that device ID in the configuration file.
    2. Save the configuration and restart Klipper.
    3. Power off and restart all devices.

    Configure CAN Device ID​

    1. Locate the Configuration File​

    Find the printer.cfg configuration file based on the web interface you are using:

    Fluidd
    Click the {...} icon in the left navigation bar, then find printer.cfg.

    Loading...

    Mainsail
    Click Machine in the top navigation bar, then find printer.cfg.

    Loading...

    2. Add Device Configuration​

    Add the toolboard configuration to printer.cfg:

    [mcu toolboard]
    canbus_uuid: <Enter the ID found here>
    Configuration Notes
    • toolboard is the toolboard name; please modify it according to your actual situation.
    • For a mainboard ID, the configuration section should be [mcu].
    • In a normal configuration, the mainboard uses [mcu], and toolboards use [mcu toolboard].

    3. Save and Restart​

    1. Click the SAVE & RESTART button in the top right corner.
    2. The system will automatically save the configuration and restart Klipper.
    Loading...
    Note

    All IDs appearing in this document are examples. The actual ID for each mainboard is different. Please modify and fill in the ID based on what you actually obtain.

Loading...