FAST System Image Flashing
Preparation Before System Flashing
Preparing Required Devices
- TF Card Boot
- M2WE Boot
Required Devices:
- Card reader
- One TF card (capacity 16GB-128GB, transfer speed Class 10 or above)
- Windows computer (Win7, Win10, Win11 all supported)
Recommendations:
- It is recommended to use well-known brands such as SanDisk, Samsung, Kioxia for the TF card
- The use of unbranded TF cards is prohibited, as they may cause flashing failures or system instability
Compatibility Notes:
- The
Lite seriesandMINI-PAD seriesdo not support M2WE
Required Devices:
- M2WE (FLY proprietary device)
- M2SD (FLY flashing device)
- Windows computer (Win7, Win10, Win11 all supported)
Installation Diagram:
M2WE Print File Download:
Using this print file can prevent poor contact issues:
Burning the System Image
- Recently, due to server issues, the system cannot be downloaded temporarily using
Config Myprint - Please use the alternative download link for the system image, then burn the system image using
Config Myprint.
- Method 1: Config Myprint
- Method 2: Rufus
- Alternative Download Link for System Image
Step 1: Download and install the flashing tool
Download Configure Myprint System flashing tool：
Version History and Verification Files：View Config Myprint CNB Release
Install Configure Myprint：View the installation guide.
Step 2: Enter the system configuration interface
After launching the software, select from the left menu bar. System Configuration Option, enter the system flashing interface.
Step 3: Connect the storage device
Connect the memory card to be programmed to a USB port on the computer via a card reader.
Recommendation: : Using a USB 3.0 or higher interface can significantly improve flashing speed.
Step 4: Identify the storage device
Click Storage devices Beside Refresh Button to ensure the system correctly recognizes the connected memory card.
Step 5: Select the Device Model
Click Device Selection, and select the corresponding configuration plan based on the device model you are using.
Step 6: Perform the flashing operation
After confirming the device selection is correct, click Start Flashing Button.
- Understood.Permanent EraseAll data on the memory card.
- Please ensure you have backed up important files before flashing.
- Please do not disconnect the device during the flashing process.
Step 7: Complete the Flashing
Wait for the flashing progress to complete. When the interface shows the "Done" prompt, it means the system image has been successfully written.
Step 1: Download Rufus Flashing Tool
Visit the official Rufus website to download the latest version:
- Official website: Rufus Official Site
Step 2: Prepare System Image File
- Download the FlyOS system image file from the official channel:
- Download link: FlyOS Official Download
- It is recommended to always use the latest version for optimal performance and features
- The
v1.3.XXin the version number represents different minor versions based on the 1.3 series
| System Version | Chip Platform | Compatible Devices |
|---|---|---|
| FlyOS-Fast-H618-v1.3.XX | Allwinner H618 | FLY-C5, FLY-C5 V1.1, FLY-C8P, FLY-Pi V3 |
| FlyOS-Fast-H5-v1.3.XX | Allwinner H5 | FLY-Pi series, FLY-C8 series, FLY-Gemini series |
| FlyOS-Fast-H3-v1.3.XX | Allwinner H3 | FLY-Pi Lite2 series, FLY-MiniPad |
Step 3: Connect Storage Device
- Insert the memory card into the computer's USB port using a card reader
Step 4: Launch Rufus and Configure
- Run the Rufus program
- Select your TF card from the "Device" dropdown menu
- Click the "Select" button, browse and choose the downloaded system image file
Step 5: Start Flashing
- After confirming all settings are correct, click the "Start" button
- The system will display a warning indicating that all data on the device will be cleared
- Click "OK" to continue
- This operation will permanently erase all data on the TF card
- Please make sure to back up important files before flashing
- Do not remove the TF card during the flashing process
Step 6: Wait for Flashing to Complete
- The flashing progress bar shows the current progress
- The flashing time depends on the TF card speed and image size, usually taking 5-15 minutes
- When the status shows "Ready", the flashing is complete
Step 7: Safely Remove the Device
- Close the Rufus program
- Safely eject the TF card in the Windows system
- After removing the TF card, it can be inserted into the device for use
- Net disk download link
System Startup Notes
Important: It is recommended to complete system configuration (WiFi, SSH, screen, etc.) before first system startup to avoid configuration issues after boot.
For detailed configuration guidance, please refer to: System Configuration Options
Before starting, completely shut down the printer and disconnect the power supply. Do not plug or unplug wiring harnesses, organize interface cable routing, or touch terminals while the system is powered on.
- Use the input interface, voltage, and power specified in the corresponding product documentation. Do not directly apply power parameters from other host boards or motherboards to the current device.
- Maintain stable power supply during first startup and system expansion; insufficient power may cause startup failure, storage card corruption, or expansion interruption.
- The FPC screen cable must be connected only after the device is completely powered off, and confirm the interface orientation is correct.